(資料圖片)

1. 簡介

ArmSoM-W3 RK3588 開發板中已集成AN總線：

專欄總目錄CAN(controller Area Network)CAN BUS:控制器局域網絡總線目前世界上絕大多數汽車制造廠商都采用CAN總線來實現汽車內部控制系統之間的數據通信。RK3568/RK3588的CAN驅動文件：drivers/net/can/rockchip/rockchip_canfd.c

2. 內核配置

rockchip_linux_defconfig配置：

CONFIG_CAN=yCONFIG_CAN_DEV=yCONFIG_CAN_ROCKCHIP=yCONFIG_CANFD_ROCKCHIP=y

內核配置：

cd kernelmake ARCH=arm64 menuconfigmake savedefconfig

選擇：Networking support ---> CAN bus subsystem support ( )--->CAN Device Drivers() ---> Platform CAN drivers with Netlink support(*)

3. DTS 節點配置

3.1 主要參數:

interrupts = ;

轉換完成，產生中斷信號。

clock

時鐘屬性，用于驅動開關clk，reset屬性，用于每次復位總線。

pinctrl

3.2 公共配置 kernel-5.10/arch/arm64/boot/dts/rockchip/rk3588s.dtsi

can1: can@fea60000 {            compatible = "rockchip,can-2.0";            reg = < 0x0 0xfea60000 0x0 0x1000 >;            interrupts = < GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH >;            clocks = < &cru CLK_CAN1 >, < &cru PCLK_CAN1 >;            clock-names = "baudclk", "apb_pclk";            resets = < &cru SRST_CAN1 >, < &cru SRST_P_CAN1 >;            reset-names = "can", "can-apb";            pinctrl-names = "default";            pinctrl-0 = < &can1m0_pins >;            tx-fifo-depth = < 1 >;            rx-fifo-depth = < 6 >;            status = "disabled";    };

compatible = “rockchip,can-1.0” ，rockchip,can-1.0用來匹配can控制器驅動。compatible = “rockchip,can-2.0” ，rockchip,can-2.0用來匹配canfd控制器驅動。assigned-clock-rates用來配置can的始終頻率，如果CAN的比特率低于等于3M建議修改CAN時鐘到100M，信號更穩定。高于3M比特率的，時鐘設置200M就可以。pinctrl配置：根據實際板卡連接情況配置can_h和can_l的iomux作為can功能使用。

3.3 板級配置 kernel-5.10/arch/arm64/boot/dts/rockchip/rk3588-armsom-w3.dts

/* can1 */&can1 {        status = "okay";        assigned-clocks = < &cru CLK_CAN1 >;        assigned-clock-rates = < 200000000 >;        pinctrl-names = "default";        pinctrl-0 = < &can1m1_pins >;      //根據原理圖配置};

由于系統根據上述dts節點創建的CAN設備只有一個，而第一個創建的設備為CAN0

4. 調試

查詢當前?絡設備:

ifconfig -a

CAN啟動

ip link set can0 down   //關閉CANip link set can0 type can bitrate 500000   //設置?特率500KHzip -details -statistics link show can0    //打印can0信息ip link set can0 up     //啟動CAN

CAN發送

cansend can0 123#DEADBEEF            //發送（標準幀,數據幀,ID:123,date:DEADBEEF）cansend can0 123#R                            //發送（標準幀,遠程幀,ID:123）cansend can0 00000123#12345678    //發送（擴展幀,數據幀,ID:00000123,date:DEADBEEF）cansend can0 00000123#R                 //發送（擴展幀,遠程幀,ID:00000123）

CAN接收

candump can0       //candump can0

審核編輯：湯梓紅